The publisher is making several good pointers regarding Installing A Bathtub overall in this post underneath.
Mounting a tub isn't exactly brain surgery, yet it does need solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bath tub with a new one is likewise a moderately tough project. If the old bathtub is conveniently easily accessible, the job can move immediately; if you have to open up a wall surface to remove the old tub and also place the new bathtub, the task is a lot harder. In either situation, the job is within a house handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also embeded in the new one. See to it you have qualified on your own for the job and are comfortable attempting it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you might need a specialist plumber to make tube links.
This article will certainly aid you install a new tub in your bathroom if you have already purchased a new tub and don't need to transform the setup of your previous supply of water pipelines.
Your tools as well as material list must consist of the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly come from the pipelines. Once the supply pipes have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in area in between the tap as well as the sink. Safeguard the faucet in place with the supplier given backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap ports. The former type needs to be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four small points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub until the level checks out degree.
To install faucets, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Switch on the water system and check all joints as well as new pipework for leakages as well as tighten them if essential. Fill up the bath tub and additionally examine the overflow outlet and also the regular electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait till the bathtub has been made use of a minimum of once as this will resolve it into its final placement.
Getting ready for the Installment
First of all, the supporting framework provided with the bathroom should be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you make use of all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall between the bathroom and also the tiling, leading to issues with dampness and feasible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components as well as installations. They are marketed in tubes and cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched paper or soft rope. Bear in mind to always load the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly very early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily readily available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very curious about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you liked the new blog posting. For those who enjoyed our blog entry plz don't forget to pass it around. We recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Best in town? Dial.